Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

基于反问题的涡轮过渡流道一体化支板设计方法

为进一步改善大涵道比涡扇发动机气动性能及燃油经济性,降低其污染物排放,控制其重量与成本,提出了一种高效的高、低压涡轮过渡流道整流支板一体化设计理念,即对原型支板与第一级低压涡轮导叶进行初步正问题一体化设计,并基于气流角全三维粘性反问题进行进一步改型设计,使得在保证自身气动性能不降低的基础上,带一体化支板涡轮过渡流道能够与高、低压涡轮实现良好匹配。以某型发动机过渡流道为算例开展了一体化设计工作,并采用三维数值模拟方法进行了设计点、非设计点流场分析评估。结果表明,设计点工况下一体化支板出口气流角以及马赫数分布均与原型导叶出口一致,验证了一体化设计的有效性。同时,带一体化支板的过渡流道总压损失从原型流道的2.49%降低到了1.02%。而在非设计工况,带一体化支板的过渡流道气流分离明显减小,具有更宽的最佳工况范围。     

温度场对航空发动机转子超转破裂的影响

CCAR33.27超转适航要求，分析和试验确定的超转转速，必须基于温度和温度梯度的最不利组合。因此，研究温度和温度梯度对超转破裂的影响有非常重要的意义。以某型航空发动机低压6级涡轮转子为例，采用极限应变方法开展了转子部件的超转破裂分析，对比了常温和高温（红线转速对应的温度分布）下转子关键轮盘应变分布趋势和应变增长规律、预测的超转破裂的起始位置和破裂转速等轮盘超转特性；针对超转破裂分析，提出了在高温条件下，经过常温超转破裂试验验证的方法应用的有效性条件。低压涡轮转子的分析结果也显示，红线转速对应的温度状态下，轮盘超转破裂转速比常温下显著降低，而高温下材料屈服强度的大幅降低则是破裂转速下降的主要原因。     

HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

航空发动机间冷器及回热器发展研究综述

近年来,航空器发展对航空发动机经济性和环保性的要求越来越高,间冷回热循环日益受到关注和重视,间冷器和回热器的研究已经成为发展间冷回热循环航空发动机的关键因素之一。本文简要介绍了间冷回热航空发动机的研究背景,回顾了国内外有关航空发动机间冷器与回热器的换热表面研究、热交换器优化工作、间冷器及回热器与航空发动机整机匹配研究和新型高温热交换器技术,提出了航空发动机间冷器及回热器相关有待深化研究的问题。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

高温合金叶片的激光熔覆修复技术研究

航空发动机高温合叶片故障件很难修复,采用先进的激光熔覆技术对高温合金叶片进行深度修理具有重要意义。通过采用合适的激光设备、熔覆粉末,并选取合理的熔覆参数以及热处理工艺等,使熔覆粉末在叶片基体上形成有效的熔覆体,该熔覆体的强度和硬度达到叶片材料性能要求,同时也能保证熔覆体与基体的结合强度,完成高温合金叶片的修复。     

高速铣削铝合金7055铣削力和铣削温度的仿真研究

采用有限元分析软件AdvantEdge模拟了航空铝合金7055高速铣削过程,获得了单个刀齿高速加工中铣削力变化曲线,预测了不同切削时间下工件及刀具上的温度分布,获得了刀具前刀面和后刀面的温度分布曲线;建立了高速铣削参数对铝合金7055铣削力和铣削温度的影响曲线,可辅助优化切削加工参数,有助于减小切削过程中刀具的磨损,改善刀具切削状态,提高刀具使用寿命.     

飞机高温高压空气导管的振动特性研究

在分析某大型客机环境控制系统的配平子系统的基础上,基于有限元软件Patran和Nastran建立了配平系统的空气导管有限元分析模型,选用Lanczos算法,对管系进行动力学模态分析,获得了系统前五阶的频率和振型.同时,考察了气体热力学参数和球形接头作动力学参数对空气导管动力学模态特性的影响.结果表明:从频率上看,配平系统Part1在45Hz以下谐振模态分布密集.从振型上看,球形接头和滑动接头处的振型变化幅度较大;从动力学特性的影响因素来看,配平系统空气导管管系的固有频率随管内温度的增加而递减,随管内压力的增加而增加;球形接头起动力矩和刚度增大会增加各阶的固有频率.研究工作对于我国大型客机空气导管系统的可靠性设计具有参考价值.     

A100钢外螺纹椭圆超声滚压强化试验研究

A100钢有较高的疲劳抗力和显著的减重效果.在航空工业中,飞机起落架主要承力件正逐步采用A100钢,且主要承力件多采用螺纹联接.为了提高螺纹疲劳寿命,提出了超声振动滚压强化工艺方法,设计了外螺纹超声滚压强化装置,进行了螺纹超声滚压强化前后性能对比试验.利用X射线分析仪、维式硬度计、粗糙度仪和疲劳试验机,分别测量了螺纹超声滚压强化前后的残余应力、维氏硬度、表面粗糙度以及疲劳寿命.结果表明,超声滚压强化后牙底残余应力提高了70％,显微硬度提高了14％,粗糙度降低了51％,600MPa应力条件下寿命提高了5倍.